Loading...
2506.2 Standards.
Gypsum board and gypsum panel products shall conform to the appropriate standards listed in Table 2506.2 and Chapter 35 and, where required for fire protection, shall conform to the provisions of Chapter 7.
Material | Standard |
Material | Standard |
Abuse resistant non-decorated interior gypsum panel products and fiber-reinforced cement panels | ASTM C 1629 |
Accessories for gypsum board | ASTM C 1047 |
Adhesives for fastening gypsum wallboard | ASTM C 557 |
Cold-formed steel studs and track, structural | AISI S200 and ASTM C 955, Section 8 |
Cold-formed steel studs and track, nonstructural | AISI S220 and ASTM C 645, Section 10 |
Elastomeric joint sealants | ASTM C 920 |
Fiber-reinforced gypsum panels | ASTM C 1278 |
Glass mat gypsum backing panel | ASTM C 1178 |
Glass mat gypsum panel 5 | ASTM C 1658 |
Glass mat gypsum substrate | ASTM C 1177 |
Joint reinforcing tape and compound | ASTM C 474; C 475 |
Nails for gypsum boards | ASTM C 514, F 547, F 1667 |
Steel screws | ASTM C 954; C 1002 |
Standard specification for gypsum board | ASTM C 1396 |
Testing gypsum and gypsum products | ASTM C 22; C 472; C 473 |
2506.2.1 Other materials.
Metal suspension systems for acoustical and lay-in panel ceilings shall conform with Section 808.1.
2506.3 Mold resistance.
Gypsum board or cement board, used in an assembly for the following areas, shall have a mold resistance rating of 10 in accordance with ASTM D 3273:
1. Interior faces of exterior walls of basements, cellars, and other below grade rooms.
2. Walls and ceilings of spaces containing condensers, water tanks, water pumps, and pressure reduction valves.
3. Walls and ceilings of laundry rooms.
4. Portions of walls within 2 feet (610 mm) of kitchen sinks to a height of 4 feet (1219 mm) above the floor.
5. Portions of walls within 2 feet (610 mm) of kitchen stoves to a height of 4 feet (1219 mm) above the floor.
6. Walls of bathrooms that are not solely water closet compartments, other than walls specifically required to be cement board.
7. Walls and ceilings in service sink closets.
8. Portions of walls within 2 feet (610 mm) of mop sinks or service sinks to a height of 4 feet (1219 mm) above the floor.
Editor's note: For related unconsolidated provisions, see Appendix A at L.L. 2014/013.
2507.1 General.
Lathing and plastering materials and accessories shall be marked by the manufacturer's designation to indicate compliance with the appropriate standards referenced in this section and stored in such a manner to protect them from the weather.
2507.2 Standards.
Lathing and plastering materials shall conform to the standards listed in Table 2507.2 and Chapter 35 and, where required for fire protection, shall also conform to the provisions of Chapter 7.
Material | Standard |
Material | Standard |
Accessories for gypsum veneer base | ASTM C 1047 |
Blended cement | ASTM C 595 |
Cold-formed steel studs and track, nonstructural | AISI S220 and ASTM C 645, Section 10 |
Cold-formed steel studs and track, structural | AISI S200 and ASTM C 955, Section 8 |
Exterior plaster bonding compounds | ASTM C 932 |
Gypsum casting and molding plaster | ASTM C 59 |
Gypsum Keene's cement | ASTM C 61 |
Gypsum plaster | ASTM C 28 |
Gypsum veneer plaster | ASTM C 587 |
Hydraulic cement | ASTM C 1157; C 1600 |
Interior bonding compounds, gypsum | ASTM C 631 |
Lime plasters | ASTM C 5; C 206 |
Masonry cement | ASTM C 91 |
Metal lath | ASTM C 847 |
Plaster aggregates Sand Perlite Vermiculite | ASTM C 35; C 897 ASTM C 35 ASTM C 35 |
Plastic cement | ASTM C 1328 |
Portland cement | ASTM C 150 |
Steel screws | ASTM C 1002; C 954 |
Welded wire lath | ASTM C 933 |
Woven wire plaster base | ASTM C 1032 |
Loading...