2506.2.1 Other materials.

Metal suspension systems for acoustical and lay-in panel ceilings shall conform with Section 808.1.

2506.3 Mold resistance.

Gypsum board or cement board, used in an assembly for the following areas, shall have a mold resistance rating of 10 in accordance with ASTM D 3273:

   1.   Interior faces of exterior walls of basements, cellars, and other below grade rooms.

   2.   Walls and ceilings of spaces containing condensers, water tanks, water pumps, and pressure reduction valves.

   3.   Walls and ceilings of laundry rooms.

   4.   Portions of walls within 2 feet (610 mm) of kitchen sinks to a height of 4 feet (1219 mm) above the floor.

   5.   Portions of walls within 2 feet (610 mm) of kitchen stoves to a height of 4 feet (1219 mm) above the floor.

   6.   Walls of bathrooms that are not solely water closet compartments, other than walls specifically required to be cement board.

   7.   Walls and ceilings in service sink closets.

   8.   Portions of walls within 2 feet (610 mm) of mop sinks or service sinks to a height of 4 feet (1219 mm) above the floor.

Editor's note: For related unconsolidated provisions, see Appendix A at L.L. 2014/013.

Section BC 2507: Lathing and Plastering

2507.1 General.

Lathing and plastering materials and accessories shall be marked by the manufacturer's designation to indicate compliance with the appropriate standards referenced in this section and stored in such a manner to protect them from the weather.

2507.2 Standards.

Lathing and plastering materials shall conform to the standards listed in Table 2507.2 and Chapter 35 and, where required for fire protection, shall also conform to the provisions of Chapter 7.

Table 2507.2
Lath, Plastering Materials and Accessories

Material	Standard
Accessories for gypsum veneer base	ASTM C 1047
Blended cement	ASTM C 595
Cold-formed steel studs and track, nonstructural	AISI S220 and ASTM C 645, Section 10
Cold-formed steel studs and track, structural	AISI S200 and ASTM C 955, Section 8
Exterior plaster bonding compounds	ASTM C 932
Gypsum casting and molding plaster	ASTM C 59
Gypsum Keene's cement	ASTM C 61
Gypsum plaster	ASTM C 28
Gypsum veneer plaster	ASTM C 587
Hydraulic cement	ASTM C 1157; C 1600
Interior bonding compounds, gypsum	ASTM C 631
Lime plasters	ASTM C 5; C 206
Masonry cement	ASTM C 91
Metal lath	ASTM C 847
Plaster aggregates    Sand    Perlite    Vermiculite	ASTM C 35; C 897 ASTM C 35 ASTM C 35
Plastic cement	ASTM C 1328
Portland cement	ASTM C 150
Steel screws	ASTM C 1002; C 954
Welded wire lath	ASTM C 933
Woven wire plaster base	ASTM C 1032

 

Section BC 2508: Gypsum Construction

2508.1 General.

Gypsum board, gypsum panel products and gypsum plaster construction shall be of the materials listed in Tables 2506.2 and 2507.2. These materials shall be assembled and installed in compliance with the appropriate standards listed in Tables 2508.1 and 2511.1.1, and Chapter 35.

Table 2508.1
Installation of Gypsum Construction

Material	Standard
Gypsum board and gypsum panel products	GA-216; ASTM C 840
Gypsum sheathing and gypsum panel products	ASTM C 1280
Gypsum board (Interior)	ASTM C 1396
Gypsum board (Exterior)	ASTM C 1396
Gypsum veneer base	ASTM C 844
Interior bathing and furring	ASTM C 841
Steel framing for gypsum board and gypsum panel products	ASTM C 754; C 1007

 

2508.2 Limitations.

Gypsum wallboard or gypsum plaster shall not be used in any exterior surface where such gypsum construction will be exposed directly to the weather. Gypsum wallboard shall not be used where there will be direct exposure to water or continuous high humidity conditions beyond the published recommendations of the manufacturer. Gypsum sheathing shall be installed on exterior surfaces in accordance with ASTM C 1280.