CHAPTER 1141
Single-Family Residence District Regulations
1141.01    Intent.
1141.03    Use regulations.
1141.05    Lot requirements.
1141.07    Setback requirements.
1141.09    Height requirements.
1141.11    Floor area requirements.
1141.13    Projections into required setbacks.
1141.15    Accessory uses and structures.
1141.17    Design criteria for one family dwellings.
1141.19    Supplemental regulations for specific uses.
1141.21    Plan review.
1141.01 INTENT.
   Single-Family Residence Districts (R-3 and R-10) and their regulations are established in order to achieve, among others, the following purposes:
   (a)   To preserve and protect the scenic beauty, the ecology and rural character of the Village for the benefit of its citizens and those of surrounding communities by essentially restricting development to low density housing.
   (b)   To regulate the bulk and location of dwellings, accessory buildings, and other structures on each lot;
   (c)   To protect the desirable characteristics and promote the stability of existing residential development;
   (d)   To promote the most desirable and beneficial use of the land in accordance with the objectives and goals of the Village of Waite Hill;
   (e)   To protect and preserve the value, appearance and use of property through the preservation of historic character consistent with the development of the Village;
   (f)   To protect and provide adequate open spaces and to insure adequate ground areas from which to obtain adequate water supply and for the safe and healthful disposal of waste; and,
   (g)   To maintain a living unit density consistent with Village tradition.
      (Ord. 2011-14. Passed 4-9-12.)
1141.03 USE REGULATIONS.
   (a)   Uses Permitted By Right. A use listed in Schedule 1141.03 shall be permitted by right as a principal use in a district when denoted by the letter "P" provided that all requirements of other Village ordinances and this Zoning Code have been met;
   (b)   Accessory Uses. An accessory use that is clearly incidental and subordinate to a use listed in Schedule 1141.03, when denoted by the letter "A," shall be permitted provided that the requirements of all other Village ordinances and this Zoning Code have been met.
   (c)   Compliance with Standards. Although a use may be indicated as a permitted principal or accessory use in a particular district, it shall not be approved on a lot unless it can be located thereon in full compliance with all of the standards and other regulations of this Code applicable to the specific use and lot in question.
   (d)   Use Not Listed in Schedule. Any use not specifically listed as a permitted principal use shall be a prohibited use in these zoning districts and shall only be permitted upon amendment of this Code and/or the Zoning Map as provided in Chapter 1131.
   (e)   Schedule 1141.03 Permitted Uses.
Schedule 1141.03
Permitted Uses(f)
R-3
R-10
Single-Family Residence
District
Single-Family Residence
District
(1)Residential
A. One-family dwelling, detached
P
P
B. Conservation Development in compliance with Chapter 1143
P
P
(2) Community Facilities/Institutions
A. Civic center 
P
P
B. Library 
P
P
C. Places of worship/church 
P
P
D. Public safety facility 
P
P
E. Public service facility 
P
P
 
Schedule 1141.03
Permitted Uses(f)
R-3
R-10
Single-Family Residence
District
Single-Family Residence
District
(3) Other
A. Agriculture (b)
P
B. Cemetery(g)
P
C. Nurseries
P
(4) Accessory Uses
A. Detached accessory buildings, including garages, barns and stables, coops, and sheds(a)
A
A
B. Fences, walls(a)
A
A
C. Greenhouse(a) (c)
A
A
D. Home occupation(a)
A
A
E. Kennel(d) (a)
A
A
F. Other accessory structures(a) (e)
A
A
G. Private recreational facilities such as, but not limited to tennis courts, stables(a)
A
A
H. Private swimming pools(a)
A
A
I. Raising of fruit and garden crops(c)
A
A
J. Signs
A
A
 
 
(a)    See Section 1141.15, Accessory Use and Structures.
(b)    Such uses shall have a minimum lot area of ten (10) acres. Equipment associated with the agricultural use shall be stored and/or parked in compliance with the required front, side and rear setbacks set forth in Schedule 1141.07.
(c)    Such crops/greenhouses shall only be for the use of the occupants of the premises.
(d)    Including only kennels or housing for household pets and/or permitted domesticated animals.
(e)    Barns, stables, coops, hutches, corrals and other similar structures are permitted pursuant to subsection 1141.15.
(f)     Other uses mandated by law shall be considered pursuant to the procedures in Chapter 1127, Site Plan Review Procedures.
(g)     Cemeteries shall have a minimum lot area of ten (10) acres. Grave markers shall not be required to comply with the required setbacks established by this Chapter.
P = Use permitted by right; A = Accessory use;
Blank cell = Use not permitted in district
(Ord. 2011-14. Passed 4-9-12.)
1141.05 LOT REQUIREMENTS.
   (a)   Minimum Lot Area and Width. The area and width of a lot shall not be less than the dimensions set forth in Schedule 1141.05 for the district in which the lot is located, except as otherwise regulated in this Code.
   (b)   Maximum Lot Coverage. The maximum lot coverage shall be as set forth in Schedule 1141.05 for the district in which the lot is located.
   (c)   Schedule 1141.05 Minimum Lot Requirements:
 
Schedule 1141.05
Minimum Lot Requirements
R-3
Single-Family Residence District
R-10 Single- Family Residence District
(1) Minimum lot area
3 acres
10 acres
(2) Minimum lot width at building setback line (a)
225 feet
250 feet
(3) Maximum lot coverage
25%
20%
(a) On curved streets, the lot width shall be the arc length of the building setback line
(Ord. 2011-14. Passed 4-9-12.)
1141.07 SETBACK REQUIREMENTS.
   Dwelling units, including attached decks, patios, and similar structures, shall be located on a lot in a manner that maintains the minimum front, side, and rear setbacks set forth in this Section for the district in which the lot is located, except as otherwise regulated in Chapter 1143, Conservation Development Regulations. The area within each required setback shall remain unobstructed by structures, except as otherwise permitted in this Code.
   (a)   Front Setback. Each lot shall maintain a front setback in compliance with Schedule 1141.07.
   (b)   Front Setback on Through Lots. On a through lot, a front setback shall be provided on each frontage equal to the minimum required front setback as set forth in Schedule 1141.07. There shall be no required rear setback on a through lot.
   (c)   Side Setbacks. Each interior and through lot shall have and maintain two side sidebacks. Schedule 1141.07 sets forth the minimum width of each side setback.
   (d)   Rear Setbacks. Each lot shall have and maintain a rear setback as specified in Schedule 1141.07.
   (e)   Schedule 1141.07 Minimum Setback Requirements:
 
Schedule 1141.07
Minimum Setback Requirements
R-3 Single-Family Residence District
R-10 Single-Family Residence District
(1) Minimum Front Setback
150 feet
200 feet
(2) Minimum Side Setback
75 feet
100 feet
(3) Minimum Rear Setback
200 feet
200 feet
 
(Ord. 2011-14. Passed 4-9-12.)
1141.09 HEIGHT REQUIREMENTS.
   All buildings and structures in any residential district shall comply with the following height regulations:
   (a)   The height of principal buildings and structures shall not exceed 2 and one-half (2.5) stories and forty (40) feet.
   (b)   The height of accessory buildings and structures shall not exceed forty (40) feet.
   (c)   During the site plan review process, an applicant may request that the Planning and Zoning Commission and the Architectural Board of Review consider an exception to the height requirement for both principal and accessory buildings and structures. Such an exception shall be not granted unless findings are made that the increased height will not adversely harm adjacent properties and the character of the surrounding area due to the setback of the proposed structure/building, the topography of the applicant's site or surrounding properties, or similar criteria.
      (Ord. 2011-14. Passed 4-9-12.)
1141.11 FLOOR AREA REQUIREMENTS.
   In order to promote healthful living conditions and to stabilize the value and character of residential areas, one-family dwelling units shall be erected, altered, moved, maintained or occupied only in accordance with the minimum floor area requirements set forth in this Section.
 
Schedule 1141.11
Minimum Floor Area Requirements(b)
R-3 Single-Family Residence District
R-10 Single-Family Residence District
(a) Total Minimum Floor Area of the One-Family Dwelling, Detached
2300 square feet
2500 square feet
(b) Minimum Main Floor Area if One-Family Dwelling, Detached is more than one (1) story (a)
1500 square feet
1500 square feet
(a) The "main floor" is that portion of the floor area having direct access to or from the ground area immediately adjacent thereto. It shall also mean the total floor areas where there is no greater difference in elevation than four (4) feet between floors.
(b) Floor area, for the purposes of this Schedule, means Floor Area, Net and does not include detached accessory buildings.
 
(Ord. 2011-14. Passed 4-9-12.)
1141.13 PROJECTIONS INTO REQUIRED SETBACKS.
   (a)   Structural Projections. A structural projection is a feature of a building that extends outside the enclosing walls as an integral and functional part of the plane, thus providing form and interest to the exterior design, and connections and protection to exterior spaces. Projections shall, however, be designed and constructed so as not to substantially interfere with the reception of sun, light, and air and the use of adjoining lots.
   (b)   Principal Building Projection Into Required Setbacks. No portion of any building may project into the setbacks established in Schedule 1141.07 above, except for cornices, belt courses, entrance canopies and similar overhanging roofed spaces, chimneys, porticos, bays, and steps that may project not more than three (3) feet into such setbacks.
(Ord. 2011-14. Passed 4-9-12.)
1141.15 ACCESSORY USES AND STRUCTURES.
    Accessory uses, buildings, and structures permitted in residential districts and associated with a one-family detached dwelling, shall conform to the location, coverage, area, and maintenance standards contained in this Section and this Code. No accessory building or use shall be established on a lot unless a principal building or use has first been established on the lot in conformance with all applicable provisions of this Zoning Code. No accessory building shall be used, enlarged, restored or maintained in such a manner as to become the main or principal use, nor shall such use be designated as an accessory use for the purpose of avoiding the intent and purpose of any provision of this Zoning Code.
   (a)   Location Requirements for Accessory Uses. An accessory building or use permitted in a residential district shall be located as set forth in Schedule 1141.15. However, an accessory use shall only be permitted to the extent such use complies with all other accessory use regulations set forth in this Zoning Code.
   (b)   Schedule 1141.15 Permitted Accessory Structures In Front, Side And Rear Yards:
 
Schedule 1141.15
Permitted Accessory Structures in Front, Side and Rear Yards
Use
Yard Permitted
Minimum Setback From Lot Line
Front
Side
Rear
(1) Detached accessory buildings, including garages, barns and stables, coops, and sheds
Rear, Side
NP
25 feet(a)
50 feet(b)
50 feet
(2) Driveways
Front, corner side, side, rear
NA
10 feet(d)
10 feet (d)
(3) Fences, walls
Front, corner side, side, rear
0 ft.
0 ft.
0 ft.
(4) Private swimming pools (a)
Rear
NP
See also Section 1141.15(f)(c)
(5) Other accessory structures such as but not limited to tennis courts, recreational equipment, etc.
Rear
NP
50 feet
50 feet
(6) Outdoor storage of recreation vehicles/equipment.
Rear
See also Section 1141.15(i)
(7) Power Conversion Facilities(e)
Rear
NP   
50 feet
Notes to Schedule 1141.15:
(a)   Applicable only to the R-3 Single-Family Residence District.
(b)   Applicable only to the R-10 Single-Family Residence District.
(c)   See also Section 1141.15(f).
(d)   During the site plan review process, an applicant may request that the Planning and Zoning Commission consider an exception to the setback requirement for driveways when site conditions, such as topography; existing buildings; existing trees/landscaping; or similar factors, necessitate a lesser driveway setback.
(e) Power Conversion Facilities, as defined in Section 1141.15(k), are conditionally
permitted if the conditions stated in Section 1141.15(k) are met.
NA   Not Applicable
NP Not Permitted
   (c)   Accessory Structures and Buildings. The total of all accessory structures and accessory buildings, excluding corrals and detached garages, shall not exceed one percent (1%) of the lot area.
   (d)   Detached Garages. Accessory detached garages shall be limited to 200 square feet for each l5,000 square feet of lot area, but not exceeding a total of 1200 square feet; provided, however, that on farms under cultivation with lots of five (5) acres or more, additional farm vehicles and equipment may be housed as may be necessary.
   (e)   Additional Regulations for Parking Areas. Accessory off-street parking spaces shall be provided in compliance with the parking requirements set forth in Chapter 1151, Off-Street Parking Regulations, which shall be located on the same lot as the dwelling served.
   (f)   Private Swimming Pools. A private swimming pool, not including farm ponds; retention basins; and lakes, shall be any pool or open tank not located within a completely enclosed building and containing or normally capable of containing water to a depth at any point greater than one and one-half (1.5) feet. No such swimming pool, exclusive of portable swimming pools with a diameter less than twelve (12) feet or with an area of less than 100 square feet, shall be allowed in any R-3 or R-10 District, except as an accessory use and unless it complies with the following conditions and requirements:
      (1)   Private swimming pools shall be located on the same zoning lot with the principle use to which it is an accessory use.
      (2)   It shall not be located, including any walks or paved areas or accessory structures adjacent thereto, closer than twenty-five (25) feet to any property line of the property and shall be a minimum of ten (10) feet from the principal building;
      (3)   The pool is intended and is to be used solely by the occupants and guests of the principal use of the property on which it is located;
      (4)   Proper drainage shall be provided to ensure that pool overflow does not affect adjacent properties;
      (5)   Whenever light is used to illuminate such pool, such lights shall be installed and shielded in such a manner as to direct light onto the pool only and not to reflect light onto any abutting residential property.
      (6)   The swimming pool shall comply with the locational and coverage requirements set forth in this Chapter.
      (7)   The construction and operation of a pool shall meet all other applicable Village regulations.
      (8)   Above-ground swimming pools will only be permitted in such circumstances that the sides of the pool will not be visible from neighboring properties or any public or private right of way.
   (g)   Fences and Walls. The purpose of this subsection is to affirm the Village policy encouraging the preservation and conservation of open space and to establish regulations controlling the location, installation, maintenance and standards for fences in order that a property owner may construct and maintain a fence which secures privacy, offers attractive landscape design and/or affords security while assuring that such fences are located and constructed so as to respect the rights and enjoyment of neighboring property owners, preserving the integrity of scenic zones, maintaining the appearance of the community, and securing the overall health, safety and public welfare of the residents of the Village.
      (1)   Scope. This subsection 1141.15(g) sets forth regulations pertaining to the location, installation, maintenance and standards for new fences in all residential zoning districts in the Village.
         A.   Any fence erected prior to the date of the adoption of this subsection 1141.15(g) which does not comply with these regulations shall be nonconforming. However, such nonconformance shall not cause an order for removal. The Village may order immediate remedial measures to alleviate or prevent any hazardous conditions when the Planning and Zoning Commission determines that such conditions, whether conforming or nonconforming, jeopardize the health and safety of residents, occupants, wildlife or domestic animals.
         B.   Trellises, living fences, hedges and other living materials shall not be deemed to constitute fences within the meaning of this subsection 1141.15(g).
         C.   All fences shall require review and approval in accordance with Chapter 1127, Site Plan Review Procedures.
      (2)   Definitions. As used in this subsection 1141.15(g), certain terms are defined as follows:
         A.   "Fence" means any structure composed of wood, iron, steel, masonry, stone or any other materials which are erected in such a manner and in such a location so as to in whole or in part enclose, secure, provide privacy, decorate, define the scope or limits of, or otherwise enhance all or an identifiable part of any premises.
         B.   "Fence open area" means the percentage of the surface area of a fence which permits passage of light and air. In computing the "fence open area" gates and/or gate opening areas shall not be considered. No area higher than the highest horizontal fence part nor lower than the lowest horizontal fence part shall be considered as contributing to or constituting a part of the surface area of a fence when computing the "fence open area" required by this Chapter.
         C.   "Surface area" means the area between the highest horizontal fence part and the lowest horizontal fence part, excluding gates and/or gate opening areas.
         D.   "Ornamental fence" means a fence constructed for its beauty or decorative effect and when viewed at a right angle, has not less than seventy-five percent (75%) of the area of its vertical plane, the area within a rectangular outline enclosing all parts of the fence in its plane, as "fence open area." Ornamental fences include:
            (i)   "Rail and post" or "split-rail fence" means a fence constructed of narrow, whole or split, wooden timbers placed horizontally between upright supporting posts; and,
            (ii)   Wrought iron fences, decorative steel fences, and aluminum fences.
      (3)   Nonconforming Fences; Plot Plan.  
         A.   Site plan review shall not be required of a person repairing, replacing or otherwise altering a conforming or nonconforming fence, provided however, that if a nonconforming fence is in such condition that more than one-half of such nonconforming fence is to be repaired, replaced or otherwise altered, site plan review shall be required in accordance with Chapter 1127, Site Plan Review Procedures.
         B.   In lieu of the submission requirements in Section 1127.17 (c), the application shall be accompanied by a plot plan, unless waived by the Zoning Administrator, drawn to scale of not less than one inch to one hundred (100) feet showing the following:
            i.   Location of all structures upon the premises;
            ii.   The location of the proposed fence;
            iii.   All property lines of the subject premises on which a fence is proposed to be constructed, erected, altered or rebuilt;
            iv.   The public street, road, highway, lane or private right of way which such premises abut;
            v.   Plans and specifications of the proposed fence;
            vi.   Material to be used in the proposed fence;
            vii.   Height of the proposed fence from established grade;
            viii.   A computation of the "fence open area" of the proposed fence; and,
            ix.   A proposed scheduled completion date.
      (4)   Fences Permitted.    
         A.   Visible from a Neighboring Residence or from a Public or Shared Right of Way. Fences which are visible from any neighboring residence or from a public or shared right of way are permitted only when they are:
            i.   "Split rail" or "rail and post" fences which do not exceed four (4) feet in height above established grade which contain seventy-five percent (75%) or greater "fence open area," are constructed of natural wood which is either untreated or treated in a natural wood finish, and whose vertical posts are separated by not less than four feet in distance from one another; or,
            ii.   "Decorative entry features" constructed of authentic stucco on masonry, stone, or brick, which do not exceed six (6) feet in height above established grade and twenty (20) feet in length at corners and entrances for aesthetic reasons; or,
            iii.   Ornamental fences which do not exceed four (4) feet in height and whose vertical posts are separated by not less than four (4) feet in distance from one another; or,
            iv.   Fences of construction and/or materials not expressly prohibited by this subsection 1141.15(g) and which the Village Architectural Board of Review shall expressly determine to be harmonious and compatible with those objectives expressed in Section 7.34 of the Village Charter, which section is incorporated by reference into this section as if fully rewritten herein, and this subsection 1151.15(g). Harmonious and compatible fencing materials may include finished wood, iron, metal, or synthetic look-alike products provided such are approved by the Village Architectural Board of Review as provided for in this subsection 1141.15(g).
         B.   Not Visible from any Neighboring Residence or From a Public or Shared Right of Way. Fences are permitted in areas not visible from any neighboring residence or from a public or shared right of way if they are:
            i.   Fences authorized in subsection A. hereof; or,
            ii.   Fences of any materials or construction other than chain link, barbed wire, or stockade which are no higher than six (6) feet above established grade.
         C.   Chain Link Enclosures for Tennis Courts or other Similar Recreation Areas, Swimming Pools, or Pet Runs. Metal chain link fences are permitted if they have seventy-five percent (75%) or greater "fence open area" and if they:
            i.   Do not exceed ten (10) feet in height and enclose a tennis court or other similar recreational area; or
            ii.   Do not exceed five (5) feet in height and enclose a swimming pool; or
            iii.   Do not exceed six (6) feet in height and enclose a pet run.
A landscape plan to screen such enclosures may be required when the plot plan is reviewed in accordance with Chapter 1127, Site Plan Review Procedures.
           D.   The provisions of subsections A. and B. hereof shall not apply to fence enclosures authorized by this subsection C.
      (5)   Fences Materials.  
         A.   No person shall construct or maintain a stockade or barbed wire fence within the Village.
         B.   Unless permitted by subsection 1141.15(g)(4)C, no person shall construct or maintain a chain link fence within the Village.
      (6)   Temporary Fences. The provisions of this subsection shall not apply to any temporary fence enclosing a permitted construction site or any temporary snow fence erected to prevent the drifting of snow provided that such temporary snow fence is erected not earlier than October 15 and is removed not later than April 15.
      (7)   General Conditions.
         A.   All fences shall be maintained in good repair and condition by the owner and/or occupant, and shall be structurally sound and attractively finished at all times. Any ground between the fence and property line shall be well maintained.
         B.   All fences shall be designed, constructed and finished so that the supporting members of such fence face the property of the owner of the fence.
         C.   No mesh wire fence shall be constructed unless the unfinished and sharp edges on the fence are pointing toward the ground. The top edges of all metal fences constructed, erected or maintained shall be of smooth finish with no protruding sharp edges.
         D.   In order for a fence to be constructed adjacent to, or in proximity with a property line, the property owner proposing the fence shall construct the fence so that it can be easily dismantled from its owner's side for the purpose of maintaining it entirely within the owner's property.
         E.   At all street intersections, the intersection of private driveways and public rights of way, and the intersections of two (2) driveways, and ten (10) feet in any direction therefrom, there shall be no fence or dense vegetation, which in the judgment of the Chief of Police, may impede the clear vision between vehicles and pedestrians at such intersections.
      (8)   Inspection; Appeal to Board of Zoning Appeals.  
         A.   Inspection. It shall be the duty of each property owner to determine property lines and to ascertain that the fence thus constructed does not deviate from the plans as approved by the Village, and that such fence does not encroach upon another lot or parcel of land. The Village shall furnish such inspection as is deemed necessary to determine that the fence is constructed in accordance with the plan submitted for site plan review, provided however, that the issuance of the zoning certificate by the Village shall not be construed to mean that the Village has determined that the fence is not encroaching upon another lot, nor shall it relieve the property owner of any duty imposed upon him by this or any other ordinance, code and/or the general laws of the State of Ohio.
         B.   Appeals to Board of Zoning Appeals. Any party adversely affected, including the Village, may take a written appeal to the Board of Zoning Appeals in accordance with Chapter 1133, Appeals and Variances. The Board of Zoning Appeals may permit variances from these regulations in cases where exceptional physical conditions exist, or the established regulations or standards of this section are inappropriate or inapplicable, and the requested variances will not adversely affect the purposes of this subsection 1141.15(g).
   (h)   Additional Regulations for Vehicles.  
      (1)   The repainting, rebuilding, overhauling, or dismantling of a vehicle or the storage of tires, motor, body or other parts in an open yard is prohibited on a residential lot.
      (2)   The overnight parking or the outdoor storage of commercial motor vehicles, as defined in Section 341.01, is prohibited.
      (3)   The parking or storing of vehicles shall not be permitted in the established lawn areas of residential lots, except as otherwise permitted in this Code.
   (i)   Outdoor Storage of Recreation Vehicles/Equipment. The outside storage and parking of recreational vehicle/equipment shall be permitted as an accessory use subject to the following conditions and limitations:
      (1)   They shall not be connected to electricity, water, gas, or sanitary sewer facilities, and at no time shall this vehicle/equipment be used for living or housekeeping purposes.
      (2)   If the recreational vehicle/equipment is parked or stored outside, it shall be parked in the rear yard; and it shall not be stored in any side setback. Such recreational vehicle/equipment shall be screened from adjacent property and the public right-of-way in accordance with subsection 1141.15 (g)(7)C.
      (3)   Notwithstanding the provisions of this subsection, recreational vehicle/equipment may be parked anywhere on the premises for loading or unloading purposes, for a period of not more than 48 hours.
      (4)   The area surrounding the parked or stored recreational vehicle/equipment shall be maintained pursuant to all applicable Village ordinances, codes, standards, and regulations.
      (5)   All recreational vehicle/equipment shall be kept operable and in good repair and carry a current year's license or registration.
      (6)   The impervious area used for the outside storage and parking of recreational vehicle/equipment shall be included in the computation of the maximum lot coverage.
   (j)   Home Occupation. The purpose of this section is to set forth regulations, which control the establishment and operation of home occupations. The intent of these regulations is to control the non-residential use of a residential dwelling unit so that the non-residential use is limited to an accessory use, and shall not in any way adversely affect the uses permitted in the residence district of which they are a part. Compliance with these regulations should result in all home occupations being located and conducted in such a manner that their existence is not detectable in any manner from the outside of the dwelling unit.
Home occupations shall be a permitted accessory use when conducted in compliance with the following standards. When not in compliance with the following standards, such home occupation shall be declared a nuisance pursuant to the Codified Ordinances of the Village of Waite Hill.
      (1)   Home occupations shall be clearly incidental and secondary in importance to the use of the dwelling for residential purposes.
      (2)   No more than one (1) person other than members of the family residing on the premises shall be engaged in such home occupation;
      (3)   The occupation shall be conducted wholly within a principal or accessory building, and the space used for the home occupation shall not occupy more than twenty-five percent (25%) of the net floor area of all buildings on the zoning lot.
      (4)   No home occupation shall be carried on that will substantially change the residential character of the dwelling or the accessory building.
      (5)   All storage of materials, goods, supplies or equipment related to the operation of a home occupation shall be inside the principal or accessory building.
      (6)   The number of automobiles or trucks attracted to the premise shall not be greater than that which is normally associated with residential uses.
      (7)   The noise, fumes, and vibrations generated by a home occupation shall not be greater than the expected levels or amounts typical of a residential area, and such noise level, fumes or vibrations shall not create a nuisance in the neighborhood.
      (8)   No wholesale, jobbing, or retail business shall be permitted unless it is conducted entirely by mail, telephone, or electronically and does not involve the receipt, delivery, sale or storage of merchandise on or from the premises.
   (k)   Power Conversion Facilities. "Power Conversion Facilities" means equipment that is designed for the conversion of wind, solar, or other natural energy, or storage of same, and is permitted as an accessory use to the residential use of property, subject to the regulations set forth in this section.
      (1)    No Power Conversion Facility shall be visible from any neighboring property or from any public right of way, except as otherwise provided by this chapter, nor shall a Power Conversion Facility compromise the design or aesthetic appearance of a residence, as determined by the Architectural Board of Review.
      (2)    Solar Energy Systems: A Solar Energy System consists of photovoltaic cells and related accessories that are designed to convert solar energy into electrical energy; or a system consisting of solar thermal collectors, parabolic reflectors, or similar structures that are designed to harness solar energy for use as thermal energy for heating water or air or for some other permitted use; and may include battery storage systems on the property meeting requirements of Section 1141.15(k). Solar Energy Systems are a conditionally permitted accessory use, provided that the following standards and conditions are met:
         A.    Subject to the review and approval of the Planning and Zoning Commission solar panels shall be placed on the portion of the roof of any residential or accessory building so that the panel or panels:
            i.    Are not visible from any street or sidewalk at the front of the property or from any neighboring residence;
            ii.    Do not extend beyond the edge of the roof;
            iii.    Are placed parallel to the plane of a pitched roof (sloped in excess of four inches (4") per foot) and are not more than eighteen inches (18") above the surface of the roof when measured to the top of the solar panel; and
            iv.    To provide proper system performance for low slope (pitches less than four inches (4") per foot) and flat roofs, and then alternative heights and configurations may be considered to exceed minimum height above the roof as approved by the Planning Commission.
         B.    Solar panels may only be considered in roof locations that are not in compliance with subsection (k)(1) above, or not in a rear yard, when the applicant has demonstrated to the satisfaction of the Planning and Zoning Commission that:
            i.    There are no alternative locations in compliance with subsection (k)(1);
            ii.    The proposed panels and their location(s) are designed to minimize any adverse impacts to the neighborhood; and
            iii.    The size and location of any structure is the minimum necessary to serve the needs of the building(s) on the property.
         C.    Solar equipment (other than the panels) shall be placed only inside a building or in the rear yard.
         D.    Any ground mounted solar panel systems or related equipment being proposed shall:
            i.    Only be located in a rear yard and no less than fifty feet (50') from any side or rear yard lot line;
            ii.    Not exceed a height that is necessary, as determined by the Planning and Zoning Commission, to perform the intended function while permitting reasonable maintenance of both the solar panels and equipment and the ground on which they are located;
            iii.    Comprise only the minimum area needed to provide the energy necessary to serve the property but in no case have a maximum area greater than one thousand (1,000) square feet when measured using a horizontal plane around the perimeter of the system and such area shall not be in addition to that allowed for in the maximum area allowances for accessory buildings and structures as otherwise regulated in each zoning district; and
            iv.    Be reasonably screened from view of an adjacent property or a street, as determined by the Planning and Zoning Commission, by existing or proposed landscaping and/or fencing. Existing and proposed screening shall be shown on the plans submitted with the application.
         E.    Solar panels and related equipment shall be located, oriented, or screened and constructed of such material as to prevent, to the fullest extent practicable, glare from solar panels being directed at any other person, building or public right of way.
         F.    An application for a Solar Energy System to be reviewed by the Lake County Building Department, the fire authority having jurisdiction over the Village, and the Planning and Zoning Commission and shall include:
            i.    Complete architectural and engineering drawings, adequately scaled and dimensioned, depicting the location, installation, mounting, anchorage details, appearance on the building and details for wiring and connections, and battery storage system as noted in subsection (k)(2)F.iii. below for the proposed system;
            ii.    The manufacturer's specifications for the system being proposed;
            iii.    Where Battery Storage Systems are proposed for Solar Energy Systems, they shall include, without limitation:
               a.   A list of equipment.
               b.   A site plan, showing the location of the Battery Storage System.
               c.   A plan for ventilation.
               d.   A plan for fire containment.
               e.   The location for supporting structures for batteries and equipment.
               f.   A full plan of the electrical system, including device locations and wiring plan(s).
            iv.    A description and plan of the trees and/or other vegetation that need to be trimmed or removed from the site for evaluating the removal of such vegetation; and
            v.    Verification that the installer has professional training, NABCEP certification and licensure as required for work requiring such, by state or federal law.
         G.    When locating a solar panel, it is the property owner's responsibility to consider current and future development, growth of trees and vegetation, and other obstructions that might interfere with solar access. Nothing in this section shall prohibit the owner of the solar energy conversion system from obtaining a solar access easement from any person.
         H.    All solar energy systems must be reviewed and approved by the Lake County Building Department, the fire authority having jurisdiction over the Village, and the Planning and Zoning Commission prior to the issuance of a permit to install the system.
      (3)    These regulations do not apply to geothermal energy conversion facilities, which convert geothermal energy into energy that is usable for residential use, which are permitted if they cannot be observed from any neighboring property or public right of way.
      (4)    These regulations do not apply to facilities that generate electrical energy from the use of natural gas, propane, or similar energy sources, which facilities are permitted and subject to approval of the Planning and Zoning Commission as to location and screening of such facilities to minimize any negative impacts on neighboring residences.
         (Ord. 2022-10. Passed 9-12-22.)
1141.17 DESIGN CRITERIA FOR ONE FAMILY DWELLINGS.
   (a)   The purpose of the following design criteria is to further the goals of the Village including:
      (1)   The promotion and protection of the public health, convenience, comfort, prosperity and general welfare by regulating the exterior design of buildings and structures to assure orderly and reasonably harmonious development;
      (2)   The protection and preservation of property values when buildings are constructed or altered to prevent the impairment or destruction of real estate values;
      (3)   The regulation, according to accepted and recognized architectural principles, of the design and use of materials on all principal and accessory buildings to be created, moved, altered, remodeled or repaired;
      (4)   The construction of high-quality buildings in terms of the design and materials selected given the architectural style of the building; and,
      (5)   The prevention of the harmful effects of excessively similar, dissimilar, or inappropriate exterior design of buildings or structures in relation to the exterior design of buildings prevailing in the Village.
  
   (b)   The provisions of this Section shall apply to all residential development including principal and accessory buildings. Any addition, remodeling, relocation, or construction requiring review shall adhere to the guidelines in this Section, where applicable. The Architectural Board of Review may exempt applicants from these standards when the exterior building modifications are minor in nature, meaning the design modifications will have no discernable impact on neighboring properties, the public, the public right-of-way, or those intended to occupy or use the proposed development.
   (c)   Character of Dwellings. Principal dwellings and accessory building are to be designed and located on the site and be of a scale to complement buildings in close proximity and enhance the character of the surrounding area by having features that are appropriate and compatible with existing buildings and structures. In making this determination, the following shall be considered:
      (1)   Building height, width, and general proportions;
      (2)   Architectural features, including patterns of windows and doors, roof pitch, balconies, porches, shutters, dormers, eaves and other decorative detail;
      (3)   Building materials.
      (4)   Explanation Of Terms. Certain terms and words shall be interpreted with regard to the following explanations:
         A.   Appropriateness. A proposal is judged to be appropriate when it respects the existing architectural style of a building or buildings and fits comfortably within its setting, neighborhood and overall community. This condition applies to landscaping and accessory structures, as well.
         B.   Compatibility. A design or a material selection is compatible when it does not strongly deviate from the buildings on the site, or the overall character of the neighborhood. To be compatible does not require look alike designs, but rather designs that reflect some aspects of the building or buildings in the general vicinity, such as scale of windows, overhangs, building materials, patterns of siding, roof slope. Conversely, incompatibility occurs when an architectural design, landscape design or accessory building proposal is aesthetically harsh or overwhelming relative to its neighbors. The Architectural Board of Review need not consider compatibility when the building under review is determined to be so isolated that it has no bearing on adjacent property or the neighborhood.
         C.   Proportion. The relationship of parts of a building, landscape, structures, or buildings to each other and to the whole balance.
         D.   Proximity. Proximity shall be considered in terms of the potential for one property, by virtue of its location, to materially affect other properties. In determining a property to be in proximity to another, the following factors shall be considered:
            i.   The visibility of both properties from a common point; or,
            ii.   The location of both properties within a relatively compact network of streets, walkways, or spaces.
   (d)   Façade Articulation. The articulation of facades and the massing of structures give them richness and scale. Long uninterrupted exterior walls should be avoided. All building walls should have relief to create interest and reduce bulk.
   (e)   Roof Articulation. For sloped roofs, both vertical and horizontal articulation is encouraged. Rooflines should be representative of the design and scale of surrounding dwellings. Roof articulation may be achieved by changes in plane and/or the use of traditional roof forms such as gables, hips, and dormers.
(Ord. 2011-14. Passed 4-9-12.)
Loading...