A. The provisions of this section are applicable to the following affected facilities: all stationary gas turbines, oil-fired turbines, or internal combustion engines. This section also applies to an installation operated for the purpose of producing electric or mechanical power with a resulting discharge of sulfur dioxide in the installation's effluent gases.
B. For purposes of this section, the heat input shall be the aggregate heat content of all fuels whose products of combustion pass through a stack or other outlet. Compliance tests shall be conducted during operation at the normal rated capacity of each unit. The total heat input of all operating fuel-burning units on a plant or premises shall be used for determining the maximum allowable amount of particulate matter which may be emitted.
C. No person shall cause, allow or permit the emission of particulate matter, caused by combustion of fuel, from any stationary rotating machinery in excess of the amounts calculated by one of the following equations:
1. For equipment having a heat input rate of 4200 million BTU per hour or less, the maximum allowable emissions shall be determined by the following equation:
E = 1.02Q 0.769
where:
E = The maximum allowable particulate emissions rate in pounds-mass per hour.
Q = The heat input in million BTU per hour.
2. For equipment having a heat input rate greater than 4200 million BTU per hour, the maximum allowable emissions shall be determined by the following equation:
E = 17.0Q 0.432
where "E" and "Q" have the same meaning as in subdivision 1 of this subsection.
D. The actual values shall be calculated from the applicable equations and rounded off to two decimal places.
E. No person shall cause, allow or permit to be emitted into the atmosphere from any stationary rotating machinery, smoke for any period greater than ten consecutive seconds which exceeds forty percent opacity. Visible emissions when starting cold equipment shall be exempt from this requirement for the first ten minutes.
F. When low sulfur oil is fired, stationary rotating machinery installations shall burn fuel which limits the emission of sulfur dioxide to 1.0 pound per million BTU heat input.
G. When high sulfur oil is fired, stationary rotating machinery installations shall not emit more than 2.2 pounds of sulfur dioxide per million BTU heat input.
H. Any permit issued for the operation of an existing source, or any renewal or modification of such a permit, shall include a condition prohibiting the use of high sulfur oil by the permittee. This condition may not be included in the permit if the applicant demonstrates to the satisfaction of the control officer both that sufficient quantities of low sulfur oil are not available for use by the source and that it has adequate facilities and contingency plans to insure that the sulfur dioxide ambient air quality standards set forth in Section 17.08.020 will not be violated.
1. The terms of the permit may authorize the use of high sulfur oil under such conditions as are justified.
2. In cases where the permittee is authorized to use high sulfur oil, the permittee shall submit to the control officer monthly reports detailing efforts to obtain low sulfur oil.
3. When the conditions justifying the use of high sulfur oil no longer exist, the permit shall be modified accordingly.
4. Nothing in this section shall be construed as allowing the use of a supplementary control system or other form of dispersion technology.
I. The owner or operator of any stationary rotating machinery subject to the provisions of this section shall record daily the sulfur content and lower heating value of the fuel being fired in the machine.
J. The owner or operator of any stationary rotating machinery subject to the provisions of this section shall report to the control officer any daily period during which the sulfur content of the fuel being fired in the machine exceeds 0.8 percent.
K. The test methods and procedures required by this section are as follows:
1. To determine compliance with the standards prescribed in subsections C through H of this section, the following reference methods shall be used:
a. Reference Method 20 in 40 CFR 60, Appendix A for the concentration of sulfur dioxide and oxygen.
b. ASTM Method D-129-91 (Test Method for Sulfur in Petroleum Products) (General Bomb Method) for the sulfur content of liquid fuels.
c. ASTM Method D-1072-90 (Test Method for Total Sulfur in Fuel Gases) for the sulfur content of gaseous fuels.
2. To determine compliance with the standards prescribed in subsection J of this section, the following reference methods in the Arizona Testing Manual shall be used:
a. ASTM Method D-129-91 (Test Method for Sulfur in Petroleum Products) (General Bomb Method) for the sulfur content of liquid fuels.
b. ASTM Method D-1072-90 (Test Method for Total Sulfur in Fuel Gases) for the sulfur content of gaseous fuels.
(Ord. 1993-128 § 4 (part), 1993)