15-15-3: CONDITIONAL USES:

The following uses shall be permitted only when authorized by a conditional use permit as provided in chapter 7 of this title:

Planned residential unit development (PRUD), in accordance with chapter 8 of this title.

Private park, playground, or recreation area, but not including privately owned commercial amusement business.

Privately operated concession or amusement business in a public park.

Public school bus terminal, subject to the following standards:

   A.   School buses are owned and operated by the School District;

   B.   Facility is located in conjunction with school administrative offices; and

   C.   Accessory maintenance and fuel operations must be specifically applied for and approved.

Public utility substation or water storage reservoir developed by a public agency.

Residential infill development in the R-1-5 and R-1-6 Zones, in accordance with chapter 11 of this title.

(Ord. 2015-52, 11-24-2015)

15-15-4: SITE DEVELOPMENT STANDARDS:

   A.   Minimum Lot Area:

      1.   R-1-10 Zone: Ten thousand (10,000) square feet; corner lot, eleven thousand (11,000) square feet.

      2.   R-1-8 Zone: Eight thousand (8,000) square feet; corner lot, nine thousand (9,000) square feet.

      3.   R-1-6 Zone: Six thousand (6,000) square feet for dwelling and seven thousand five hundred (7,500) square feet for other main building; corner lot, seven thousand (7,000) square feet.

      4.   R-1-5 Zone: Five thousand (5,000) square feet for dwelling and seven thousand five hundred (7,500) square feet for other main building; corner lot, six thousand (6,000) square feet.

   B.   Lot Width:

      1.   R-1-10 Zone, minimum lot width: Eighty feet (80'); corner lot, ninety feet (90').

      2.   R-1-8 Zone, minimum lot width: Sixty five feet (65'); corner lot, seventy five feet (75').

      3.   R-1-6 Zone, minimum lot width: Sixty feet (60'); corner lot, seventy feet (70').

      4.   R-1-5 Zone:

         a.   Minimum lot width: Fifty feet (50'); corner lot, sixty feet (60').

         b.   East Central Community, minimum lot width: Forty feet (40'); corner lot sixty feet (60'); all lots with a maximum width of seventy five feet (75'), except that the depth of a corner lot may exceed seventy five feet (75').

   C.   Yard Setbacks:

      1.   Front:

         a.   R-1-10 and R-1-8 Zones, minimum setback: Thirty feet (30'), except average where fifty percent (50%) frontage is developed but not less than twenty feet (20').

         b.   R-1-6 and R-1-5 Zones except East Central Community, minimum setback: Twenty five feet (25'), except average where fifty percent (50%) frontage is developed, but not less than twenty feet (20').

         c.   East Central Community, minimum setback: Twenty feet (20') with a maximum of thirty five feet (35').

      2.   Side:

         a.   Dwelling:

            (1)   R-1-10 zone, minimum setback: Ten feet (10') with total width of two (2) side yards not less than twenty four feet (24').

            (2)   R-1-8 and R-1-6 zones, minimum setback: Eight feet (8') with total width of two (2) side yards not less than eighteen feet (18').

            (3)   R-1-5 zone, minimum setback: Five feet (5') with total width of two (2) side yards not less than fifteen feet (15').

            (4)   East Central Community, maximum setback: Ten feet (10') on one side and twenty four feet (24') on the other side.

         b.   Main Building: Other main building, twenty feet (20') each side.

         c.   Accessory building:

            (1)   R-1-10 zone: Ten feet (10'), except one foot (1') if located at least six feet (6') from rear of main building, and sixty feet (60') back from front lot line, but not closer than ten feet (10') to dwelling on adjacent lot.

            (2)   R-1-8 and R-1-6 zones: Eight feet (8'), except one foot (1') if located at least six feet (6') from rear of main building and sixty feet (60') back from front lot line, but no closer than eight feet (8') to dwelling on adjacent lot.

            (3)   R-1-5 zone: Five feet (5'), except one foot (1') if located at least six feet (6') from rear of main building, but no closer than six feet (6') to dwelling on adjacent lot.

      3.   Corner Lot: Side facing street on corner lot, twenty feet (20'), except average where fifty percent (50%) frontage is developed, but not less than fifteen feet (15').

      4.   Rear:

         a.   Main Building: Main building, thirty feet (30').

         b.   Accessory Building:

            (1)   R-1-10 zone: One foot (1'), except ten feet (10') where accessory building rears on side yard of adjacent corner lot.

            (2)   R-1-8 and R-1-6 zones: One foot (1'), except eight feet (8') where accessory building rears on side yard of adjacent corner lot.

            (3)   R-1-5 zone: One foot (1'), except six feet (6') where accessory building rears on side yard of adjacent corner lot.

   D.   Building Height:

      1.   Minimum: One story.

      2.   Maximum: Two and one-half (21/2) stories or thirty five feet (35').

   E.   Lot Coverage: No accessory building or group of accessory buildings shall cover more than twenty five percent (25%) of the rear yard area; except if the only accessory building is a garage, it may exceed the twenty five percent (25%) coverage provided it is no larger than five hundred twenty eight (528) square feet.

   F.   Landscaping: All yard areas except those areas where accessory buildings, permitted parking and accessways are specifically allowed are required to be landscaped and maintained. For new construction the landscaping shall be installed within eighteen (18) months of the time of the first occupancy of the dwelling.

(Ord. 2011-4, 1-18-2011)

15-15-5: BUILDING DESIGN STANDARDS FOR R-1-5 ZONE IN EAST CENTRAL COMMUNITY AREA:

Development in the East Central Community is subject to the following requirements:

   A.   Dwelling Sizes For Units Constructed After July 31, 2010:

      1.   Minimum Size: For a single-family dwelling the minimum square footage (excluding any basement) is one thousand one hundred (1,100) square feet for a single-story building or, for a two- story building, eight hundred (800) square feet on the main level with a total minimum of one thousand three hundred (1,300) square feet for the two (2) stories.

      2.   Maximum Size: For a single-family dwelling the maximum square footage (excluding any basement) is two thousand four hundred (2,400) square feet for a single-story building or, for a two- story building, one thousand four hundred (1,400) square feet on the main level and two thousand eight hundred (2,800) square feet for the total of two (2) stories. If more than fifty percent (50%) of the same side of the block has dwellings larger than these maximums for either single-story or two-story dwellings respectively, then the new construction can exceed these maximums but cannot be larger than the largest home on that block in square footage.

   B.   Exterior Building Materials And Design: In order to protect the historic integrity established by the existing buildings in this zone, the building design and exterior finishes of all new dwellings, garages, or accessory structures constructed in the East Central Community, including new additions or exterior remodeling of existing buildings or accessory structures after July 31, 2010, shall comply with the following design requirements and materials. Properties which are on the local historic register are subject to the requirements of the local landmarks commission and are exempt from these standards if a certificate of historic appropriateness grants approval contrary to these standards.

      1.   Exterior Solid Wall Surface Materials:

         a.   Face brick (maximum brick size 25/8 inches by 95/8 inches);

         b.   Wood lap or tongue and groove wood siding that creates horizontal lines;

         c.   Hardiplank or similar nonvinyl or nonmetal siding material that creates a horizontal wood lap appearance; or

         d.   Stucco or stucco appearing material so long as there are breaks in the wall plane with brick or stone relief areas.

         e.   A combination of brick as the base ground level material around all four (4) sides of the building and stucco appearing material, wood or hardiplank type materials above the brick; provided that on single-story buildings the brick extends at a minimum to the bottom of the windowsills and for two-story structures the brick extends at a minimum to the beginning of the second story, and the transition between the two (2) types of exterior materials is defined by a projection of the upper floor beyond the main wall or a break in the wall surface due to a porch roofline.

      2.   Exterior Solid Wall Accent Surface Materials: There are portions of a wall surface that can be designed as either areas of decoration to a building or provide a continuity of design depending on the design concept of the building. Materials used on gable ends of a building, dormers, bay projections, chimneys, quoins, pillars, and other ornamental features have a wider variety of design patterns and materials and are not limited to materials with horizontal lines. Materials that are allowable for these features are:

         a.   The same brick, wood, stucco, or hardiplank or similar nonvinyl or nonmetal siding material that creates a horizontal wood lap appearance used on the main walls of the building.

         b.   Stucco, wood, or synthetic materials that have a wood or stucco appearance and create a variation of patterns that accent the architectural feature.

         c.   Brick, stone or synthetic stone in patterns different from the major wall material.

      3.   Windows On Wall Surfaces Facing A Public Street: The minimum amount of glass for the ground floor level of a dwelling facing the street is fifteen percent (15%) of the wall surface and, for dwellings on a corner lot, ten percent (10%) of the wall surface facing the side street. For two-story dwellings, the minimum amount of glass for the second story is ten percent (10%) of the wall surface facing the street and, for the second story of a dwelling on a corner lot, seven and one-half percent (7.5%) of the second story wall facing the side street.

      4.   Roof Design And Materials: Only roof designs that either are gabled, gambrel, or hip design are permitted. The minimum roof slope is three to twelve (3:12) (3 rise to 12 length). The roof exterior surface is limited to asphalt shingles, wood shake or wood shingle, tile or tile appearing material or composite materials that have the same visual appearance as the permitted materials.

      5.   Entry Porches: New dwellings are required to have a main entrance facing the street with a porch and associated roof over that porch. The roof covering over the porch shall be an extension of the house in design and building materials and shall have a minimum projection over the front door of four feet (4') and a maximum of eight feet (8'). The porch shall be a minimum of five feet (5') wide along the front face of the building and may extend the full length of the front of the dwelling. It must remain open on two (2) sides (except for insect see through screens) and cannot have glass or walls taller than forty inches (40") around the sides that are open. Existing porches as of July 31, 2010, that are open on three (3) sides shall not be enclosed on one side but shall remain open on three (3) sides. New porches which are open on three (3) sides and designed to follow the architectural lines and the material of the existing home as provided in these standards can extend the deck, roof, and columns or posts into the required front yard setback a maximum of eight feet (8') and the eave overhang a maximum of ten feet (10').

      6.   Garage Requirement, Design, Exterior Material, Locations And Other Parking Regulations:

         a.   Any dwelling constructed after July 31, 2010, is required to include, at a minimum, a one car garage as part of the construction.

         b.   New attached garages shall have the same exterior wall treatment as the dwelling to which the garage is attached.

         c.   Detached new or remodeled garages located behind the home on an interior lot may have either the same exterior wall treatment as the dwelling or may use one of the solid wall surface materials listed under subsection B1 of this section.

         d.   A garage constructed after July 31, 2010, shall have a roof slope the same as or up to sixteen percent (16%) less than the dwelling, such as 4:12 garage roof for a dwelling with a 6:12 pitch roof, shall use the same material used in the gable ends of the roof of the dwelling if such roof treatment exists on the dwelling, and the eave line of the garage roof facing the street shall have the same detail/ornamentation that is present on the exterior of the dwelling facing the street. If no ornamentation exists on the dwelling, none is required on the garage. Roofing material for the garage shall be the same roofing material as the home.

         e.   A new garage constructed on an interior lot may be freestanding and set back behind the back line of the home or attached to the rear of the home with either a side or rear garage door for vehicle entry into the garage.

         f.   A garage constructed on a corner lot may be:

            (1)   Freestanding in the rear yard if located a minimum of twenty feet (20') behind the side line of the home on the side facing a street on a corner lot and if it can meet the other required yard setbacks. If the garage cannot meet the required minimum setbacks it may be less than twenty feet (20') from the side line of the home, but in no case shall it be less than five feet (5') behind the side line of the home on the side facing a street on a corner lot (see figure i of this section);

            (2)   Behind the home on the opposite side of the lot from the street corner and not facing the street (see figure ii of this section); or

            (3)   Attached to the home with an entrance into the garage on the side of the house facing the street (see figure iii of this section).

         g.   Notwithstanding other general regulations, no recreational vehicle or accessory vehicle parking slab is permitted in the side yard setback or at the side of a dwelling in this zone and no front yard parking slab is permitted, even if no parking is available on the site in this zone.

         h.   Driveways leading to legal parking shall be a maximum of twelve feet (12') in width along the side of the home and shall flare to a width necessary to provide access to the garage and the maneuvering space needed to access the garage, except access from a side street to a garage on a corner lot may have a maximum width of twenty four feet (24').

      7.   Accessory Building Under Two Hundred (200) Square Feet, Location, Exterior Material And Other Regulations: An accessory building under two hundred (200) square feet, other than a garage or accessory dwelling unit, shall comply with the following regulations:

         a.   The accessory building may be located:

            (1)   For a dwelling on an interior lot, other than a multiple family dwelling, in a location allowed by the yard setbacks of this chapter;

            (2)   For a dwelling on a corner lot, other than a multiple family dwelling, in a location described in subsection B.6.f.(1) or (2); or

            (3)   For a multiple family dwelling, only in the rear yard.

         b.   Exterior wall finish materials are limited to:

            (1)   Brick, stone or synthetic stone;

            (2)   Wood lap, tongue and groove siding, hardi-plank, or other similar siding;

            (3)   Vinyl/resin siding, glass, stucco or stucco appearing material;

            (4)   Metal siding that has a baked enamel paint or vinyl coating. No galvanized or bare metal permitted;

            (5)   Architectural metal when approved by the planning commission on a case by case basis.

         c.   Roofing shall be made of materials designed for such application, including composition asphalt/fiberglass shingles, wood shakes, slate, tile or similar appearing materials, standing seam metal roof systems and metal shingles, and vinyl/resin materials if part of a premanufactured building. Galvanized metal surfaces, reflective surfaces or reuse materials that are not originally designed as an exterior wall or roof finish material are not permitted.

         d.   The director may allow the use of materials other than those listed above only if they are compatible with the exterior materials and finishes of the main residential building. If agreement cannot be reached on compatibility, the proposed materials/finishes shall be subject to planning commission review and approval.

      8.   Protection of Existing Brick:

         a.   Except as provided in subsection 8.b., covering of existing exterior brick with any other type of material or paint is prohibited.

         b.   Painting or sealing of unpainted brick may be approved by the planning commission if an evaluation is submitted to the planning commission that has been reviewed by the director providing information that:

            (1)   Painting or sealing of the brick is required to provide a protective surface that will limit the continued erosion of the brick;

            (2)   The paint or sealant used will preserve the brick; and

            (3)   The color of the paint or sealant will match the existing brick color.

   C.   Exceptions:

      1.   Additions, repairs or maintenance of an existing dwelling may vary from either the exterior wall materials or the roof design and materials required by subsection B of this section if the building exterior material or the roof design and materials, as of July 31, 2010, do not meet the material types or roof shape specified in this section and the addition or repair will match the existing building in exterior materials and roof shape.

      2.   If the exterior material of an existing dwelling is impossible to match because the material is no longer available, the exterior wall material may be any of the allowed exterior materials permitted in this section.

      3.   If an addition is to the rear of a dwelling on an interior lot and does not face a street, the exterior wall material may be any of the allowed exterior materials permitted in this section.

(Ord. 2011-67, 12-13-2011; amd. Ord. 2020-33, 8-4-2020; Ord. 2021-61, 12-7-2021; Ord. 2022-58, 11-15-2022)

15-15-6: FRONT YARD AND SIDE YARD FACING A STREET ON A CORNER LOT FENCING MATERIAL IN EAST CENTRAL COMMUNITY AREA:

Fences in the front yard setback or the side yard facing a street on a corner lot of the East Central Community are limited to wood, decorative metal, vinyl and plant material that may form a hedge. Brick or stone may be used as columns in the fence design. Chainlink fencing is not permitted in the front yard setback or in a side yard facing a street on a corner lot. All fencing designs other than hedges shall be open in their design with a minimum spacing between the solid members of the fence being equal to or greater than the width of the solid members of the fence. Owners of property with existing chainlink, as of July 31, 2010, shall not expand the use of chainlink fencing. If a chainlink fence is replaced it may only be replaced with a fence made with material permitted by this section.

(Ord. 2011-67, 12-13-2011)