1359.09 SEWERAGE FACILITIES.
   (a)    General Requirements. The applicant shall install sanitary sewer facilities in a manner prescribed by the approved plans. All plans shall be designed in accordance with the rules, regulations and standards of the Public Works Department, Health Department and other appropriate agencies. The Planning Commission shall not approve a subdivision unless the plans have been approved by the above agencies.
   (b)    High-Density Residential and Nonresidential Districts. Sanitary sewerage facilities shall connect with public sanitary sewerage systems. Sewers shall be installed to serve each lot and to grades and sizes required by approving officials and agencies. No individual disposal system or treatment plants (private or group disposal systems) shall be permitted. Sanitary sewerage facilities (including the installation of laterals in the right of way) shall be subject to the specifications, rules, regulations and guidelines of the Health Officer, City Engineer and
appropriate State agency.
   (c)    Low- and Medium-Density Residential Districts. Sanitary sewerage systems shall be constructed as follows:
      (1)    Where a public sanitary sewerage system is reasonably accessible the applicant shall connect with same and provide sewers accessible to each lot in the subdivision.
      (2)    Where public sanitary sewerage systems are not reasonably accessible but will become available within a reasonable time (not to exceed fifteen years), the applicant may choose one of the following alternatives:
         A.   Central sewerage system, the maintenance cost to be assessed against each property benefited. Where plans for future public sanitary sewerage systems exist, the applicant shall install the sewer lines, laterals and mains to be in permanent conformance with such plans and ready for connection to such public sewer mains; or
         B.   Individual disposal systems, provided the applicant shall install sanitary sewer lines, laterals and mains from the street curb to a point in the subdivision boundary where a future connection with the public sewer main shall be made. Sewer lines shall be laid from the house to the street line, and a connection shall be available in the home to connect from the individual disposal system to the sewer system when the public sewers become available. Such sewer system shall be capped until ready for use and shall conform to all plans for installation of the public sewer system, where such exist, and shall be ready for connection to such public sewer main.
      (3)    Where sanitary sewer systems are not reasonably accessible and will not become available for a period in excess of fifteen years, the applicant may install sewerage systems as follows:
         A.   Medium-Density Residential Districts. A central sewerage system only. No individual disposal system will be permitted. Where plans exist for a public sewer system to be built for a period in excess of fifteen years, the applicant shall install all sewer lines, laterals and mains to be in permanent conformance with such plans ready for connection to such public sewer main.
         B.   Low-Density Residential District. Individual disposal systems or central sewerage systems shall be used.
   (d)    Mandatory Connection to Public Sewer System. If a public sanitary sewer is accessible and a sanitary sewer is placed in a street or alley abutting upon property, the owner thereof shall be required to connect to such sewer for the purpose of disposing of waste, and no owner or occupant shall maintain upon any such property an individual sewage disposal system.
   (e)    Individual Disposal System Requirements. If public sewer facilities are not available and individual disposal systems are proposed, minimum lot areas shall conform to the requirements of the Zoning Ordinance (if applicable) and percolation tests and test holes shall be made as directed by the local Health Officer and the results submitted to the Health Department. The individual disposal system, including the size of the septic tank and size of the tile fields or other secondary treatment device, shall also be approved by the Health Officer.
   (f)    Design Criteria for Sanitary Sewers. 
      (1)   These design criteria are not intended to cover extraordinary situations. Deviations will be allowed and may be required in those instances where considered justified by the City Engineer.
      (2)   Design factors. Sanitary sewer systems should be designed for the ultimate tributary population. Due consideration should be given to current zoning regulations and approved planning and zoning reports where applicable. Sewer capacities should be adequate to handle the anticipated maximum hourly quantity of sewerage and industrial waste together with an adequate allowance for infiltration and other extraneous flow. The unit design flows presented hereinafter should be adequate in each case for the particular type of development indicated. Sewers shall be designed for the total tributary area using the following criteria:
One-and Two-Family Dwelling.
.02 cubic feet per second (c.f.s.)/acre.
Apartments
One-and Two story
.02 c.f.s./acre
Three-through six-story
.03 c.f.s./acre
Commercial
Small stores, offices, and Miscellaneous business
.02 c.f.s./acre
Shopping centers
.02 c.f.s./acre
High Rise-As directed by City Engineer
Industrial-As directed by City Engineer
   These design factors shall apply to watersheds of 300 acres or less. Design factors for watersheds larger than 300 acres and smaller than 1,000 acres shall be computed on the basis of a linear decrease from the applicable design factor for an area of 300 acres to a design factor of .01 c.f.s./acre for an area of 1,000 acres unless otherwise directed by the City Engineer. Design factors for watersheds larger than 1,000 acres shall be .01 c.f.s./acre unless otherwise directed by the City Engineer.
      (3)   Maximum size. The diameter of sewers proposed shall not exceed the diameter of the existing or proposed outlet, whichever is applicable, unless otherwise approved by the City Engineer.
      (4)   Minimum size. No public sewers shall be less than eight inches in diameter.
      (5)   Minimum slope. All sewers shall be designed to give mean velocities when flowing full of not less than 2.7 feet per second. All velocity and flow calculations shall be based on the Manning Formula using an N value of 0.013. The design slopes shall be evenly divisible by four. The slopes shall be minimum for the size indicated. Exceptions to these minimum slopes shall be made at the upper end of the lateral sewers serving under thirty houses. Such sewers shall have a minimum slope of 0.76 percent. Where lateral sewers serve less than ten houses, the minimum slope shall be not less than one percent. (See Table 4)
TABLE 4: Minimum Slopes for Sewer Size Indicated
Sewer Size (in Inches)
Minimum Slope in Feet Per 100 Feet
8
0.60
10
0.44
12
0.36
15
0.28
18
0.24
21
0.20
24
0.16
 
      (6)   Alignment. All sewers shall be laid with straight alignment between manholes.
      (7)   Manhole Location. Manholes shall be installed at the end of each line; at all changes in grade, size or alignment; at all intersections; and at distances not greater than 400 feet for sewers fifteen inches and smaller, and 500 feet for sewers eighteen inches in diameter and larger.
      (8)   Manholes. The difference in elevation between any incoming sewer and the manhole invert shall not exceed twelve inches except where required to match crowns. The use of drop manholes will require approval by the City Engineer. Inside drop manholes will require special considerations; however, in no case shall the minimum clear distance be less than that indicated above. When a smaller sewer joins a larger one, the crown of the smaller sewer shall not be lower than that of the larger one. The minimum drop through manholes shall be 0.2 feet.
      (9)   Sewerage locations. Sanitary sewers shall be located within street or alley rights of way unless topography dictates otherwise. When located in easements on private property, access shall be to all manholes. A manhole shall be provided at each street or alley crossing. End lines shall be extended to provide access from street or alley right of way where possible. Imposed loading shall be considered in all locations. Not less than six feet of cover shall be provided over top of pipe in street and alley rights of way or three feet in all other areas.
      (10)   Cleanouts and lampholes. Cleanout and lampholes will not be permitted.
      (11)   Water supply interconnections. There shall be no physical connection between a public or private potable water supply system and a sewer which will permit the passage of any sewage or polluted water into a potable supply. Sewers shall be kept removed from water supply wells or other water supply sources and structures.
      (12)   Relation of sewers to water mains. Relation of sewers to water mains must conform to Health Department regulations and policies.
         (Ord. 10-14. Passed 8-14-14.)